Forums

On this page you see an overview of the latest threads and discussions. If you want to see the forum, just click the link.

Re: Inside the air box CX500D DELUXE 1981 US Forum You are describing a bike that has been upside down and submerged in water, you should be lucky enough to get it running at all!	Friday, November 13, 2009
Re: Won't start YFM100A 1990 Forum Fuel line, fuel filter, float miscalibrated, float needle stuck? Anyone else	Friday, November 13, 2009
Re: How to check & change the zinger motor oil? YT60N TRI-ZINGER 1984-1985 Forum 1) lay down underneath your bike, looking at the drain plug 2) undo the plug 3) time how long it takes for your face to get covered. 4) Multiply that time (seconds)...	Friday, November 13, 2009
Re: Re: starting motor FJ1200AEC 1993 Forum It seems the starter engine in the parts fiches on the website give 36Y8180010 as a starter, which is 1984 thru 1993 starter motor... should be fine for your bike.. thank...	Thursday, November 12, 2009
Re: 12101RRP813 CYLINDER Forum It probably does not, but it seems the bore and stroke are stated, you may calculate the cc.... i can't find the salestext, I think you'd best contact a staffmember.. RAndoM...	Thursday, November 12, 2009
Re: starting motor FJ1200AEC 1993 Forum It seems the starter engine in the parts fiches on the website give 36Y8180010 as a starter, which is 1984 thru 1993 starter motor... should be fine for your bike..	Thursday, November 12, 2009
Re: 2002 honda cr250r (13101-GF5-740) PISTON Forum Hi, You are probably TWO things right now: 1) NOT looking in the right forum, for an R2 cylinder. 2) LOOKING for the 12010-KZ3-L20 cylinder assembly. Don't...	Thursday, November 12, 2009
2002 honda cr250r (13101-GF5-740) PISTON Forum i have a 2002 honda cr250r dirt bike with a bad cylinder . is the cylinder off a 1996 cr250r compatible . will it work.any and all help will be greatly appreciated . thank you ...	Thursday, November 12, 2009
starting motor FJ1200AEC 1993 Forum hi , i would like to known if the starting motor for the fj 1200 year 1991 model 3xw is compatible or same for the fj 1200 year 1986 model 1tx. thank for disponibility	Wednesday, November 11, 2009
12101RRP813 CYLINDER Forum does this cilinder have markings? 49cc/72cc? I am looking for an alloy cilinder with 72cc marking	Wednesday, November 11, 2009
honda cr 60cc PISTON (OS 0.50) Forum is os 0.50 a 43mm piston ?	Tuesday, November 10, 2009
Honda cr 60cc 1983 (13101-GF5-740) PISTON Forum I have a honda cr 60cc with a 43mm piston in it ! I need a new piston ? with rings ! I bought a (13101-GF5-740) piston and it seems to be 42mm.... ??? when i orderd it said 0,25.. can...	Tuesday, November 10, 2009
Inside the air box CX500D DELUXE 1981 US Forum I picked up an '81 CX500D that looked good in the photos on eBay (!) and I have been finding one unfortunate surprise after another. . .javascript:toggle_visibility('emoticonsSad'); I...	Tuesday, November 10, 2009
Won't start YFM100A 1990 Forum I haven't tried to start this atv in over a year and couldn't get it going so I took the bowl off of the carburator and found quite a bit of residue in the bowl. I cleaned it very good...	Monday, November 9, 2009
piston ring install order (13010-ZF6-003) RING SET,PISTON ( Forum Can someone advise which compression ring is the top one? There is one ring that is darker than the other and one ring with a slight bevel. Which one is the top compression ring? Thanks...	Monday, November 9, 2009
How to check & change the zinger motor oil? YT60N TRI-ZINGER 1984-1985 Forum Man i feel like a goof asking you this but anyway how do you know the crank oil is full, is there a drain plug under the motor maybe a bolt on the side case you pull? I got to take...	Friday, November 6, 2009
Re: Re: Re: Looking for specs on compression? YT60N TRI-ZINGER 1984-1985 Forum Whether or not it fires and runs shouldn't have anything to do with the compression. If the plugs are dry, the filter or fuel line may be blocked, or the float may be ill adjusted to prevent (sufficient) fuel from reaching the combustion area... Could also be a leak in the manifold rubber(s) where air leaks in preventing a proper combustion mixture... This is something typical, perhaps someone who's been there? Maybe i should tweek the float, that it would rise a little more? It has that metal pipe off the head & right to the new carb. I cant understand why not one drop of fuel to the plug, like wants to start then dies off, fuel come out great at the pedcock to the carb? Thank you very much, i will try after work again & let you know, i will get a new plug & some shot of either how ever you spell that. Again thanks Steve!! Got...	Friday, November 6, 2009
Re: Re: Looking for specs on compression? YT60N TRI-ZINGER 1984-1985 Forum Whether or not it fires and runs shouldn't have anything to do with the compression. If the plugs are dry, the filter or fuel line may be blocked, or the float may be ill adjusted to prevent (sufficient) fuel from reaching the combustion area... Could also be a leak in the manifold rubber(s) where air leaks in preventing a proper combustion mixture... This is something typical, perhaps someone who's been there? Maybe...	Thursday, November 5, 2009
Re: Looking for specs on compression? YT60N TRI-ZINGER 1984-1985 Forum Whether or not it fires and runs shouldn't have anything to do with the compression. If the plugs are dry, the filter or fuel line may be blocked, or the float may be ill adjusted to...	Thursday, November 5, 2009
Looking for specs on compression? YT60N TRI-ZINGER 1984-1985 Forum I am trying to get this to run for a little kid and his dad does not work on it for him to get it running, so here i go. It has good spark and the plug does not seem to get gas or flood,...	Thursday, November 5, 2009
First Prev 1 2 3 4 5 6 7 8 9 10 of 84 Next Last