Speed & Tachometers - Pilot Lamp - Key schematic Honda Cb550f1 Super Sport 550 Four 1976 (european Direct Sales)

You could pop down top your local motor spares shop, stare at their extensive bulb display for an hour or so, fail to find the bulb you wanted, become a little irritated, then drive home!
Or you could just look on-line at CMS, enter the part number from the on-line schematic into our ordering system, and be sure of the correct, genuine Honda part being promptly shipped to you - it probably cost less than your local motor spares shop anyway!

Not just a bolt, the right bolt! The right bolt for the job for which it was intended - And being genuine Honda means top quality, nicely cut thread and the correct type of zinc plating.

Renewing this part when re-furbishing the instrumentation area of your classic Honda should be mandatory to avoid damaging vibration getting through to the instruments them selves.
For all the anti-vibration rubber parts you may require for your restoration, try looking at the online 'parts list' fiche for your model, showing clearly all the parts you need, and with at a glance availability and price.

There are two good reasons to buy this Tacho cable: No one, it is cheaper than having one made up by a specialist, and number two, it will fit exactly as it is supposed to! The correct length, the correct finish if building a concourse machine and it is a genuine Honda part, just like the original.
Actually that was four good reasons, but you get our drift!

For a genuine Honda cable to suit a lower budget, this price is super low, and of course being genuine Honda will deliver the kind of fit, finish and durability that is the hall mark of Honda ownership.

If you are replacing the rubber cushion type A, then renewing this collar for what it costs would just complete the job nicely. You may also like to match this up with the collar type B: 80109061010 and the appropriate rubber cushion type B: 80106061010
To add a professional touch to all your Honda maintenance or restoration tasks, looking at our online catalogue, and, where applicable, our online 'parts list' fiche may be useful

During the course of refurbishing or renewing your tail light assembly, the anti-vibe parts should be replaced, both for insulating vibration, and sealing the bracket from moister incursion.
These WASHERS should be part of the overall replacement strategy.

Specifying only genuine Honda screws means buying parts made in Japan to Honda quality control standards - Screws that were deemed good enough by the factory when the machine rolled off the production line!
This is the 4 x 10 SELF-TAPPING SCREW.

We are delighted to ship as much or as little as your order stipulates, but the more comprehensive your order the better value, our already competitive shipping charges become!
So before placing your order for this replacement fastener related component check out the on-line gallery and schematic for your model and get even better value!
Here are just a few suggestions of other possible related fastener parts you may wish to order:

90512300000
9410106000
9410108000
9200006020
9200006016
9400106000
9411106000
9200006012
9200006028

Your overhaul will be easier to execute and with a more professional outcome when you specify new genuine Honda parts like this 5mm PLAIN WASHER rather than making do with the old corroded, maybe slightly damaged item!
For other new parts to make your task easier and with better results check out the on-line schematic for your model.

We are delighted to ship as much or as little as your order stipulates, but the more comprehensive your order the better value, our already competitive shipping charges become!
So before placing your order for this replacement fastener related component check out the on-line gallery and schematic for your model and get even better value!
Here are just a few suggestions of other possible related fastener parts you may wish to order:

90512300000
9410106000
94001080000S
9200006020
9200006016
9400106000
9411106000
9200006012
9200006028

At a low price like this, for such a high quality component, it really is not worth trying to rejuvenate the original - In this case this item should be replaced as a matter of course!
For other related components, check out our on-line schematic or for your model, and ensure you order all the parts you need to complete your task perfectly!
This is the 6mm SPRING WASHER.

At a low price like this, for such a high quality component, it really is not worth trying to rejuvenate the original - In this case this item should be replaced as a matter of course!
For other related components, check out our on-line schematic or for your model, and ensure you order all the parts you need to complete your task perfectly!
This is the 8mm SPRING WASHER.